ANSI Non-Rising Stem Hard Seal Gate Valve from ZG Valve
ANSI Non-Rising Stem Hard Seal Gate Valve from ZG Valve
ANSI Non-Rising Stem Hard Seal Gate Valve from ZG Valve
  • ANSI Non-Rising Stem Hard Seal Gate Valve from ZG Valve
  • ANSI Non-Rising Stem Hard Seal Gate Valve from ZG Valve
  • ANSI Non-Rising Stem Hard Seal Gate Valve from ZG Valve

ANSI Class125/Class150 Cast Iron/Ductile Iron Non-Rising Stem Hard Seal Gate Valve

ZG ANSI Ductile Iron Non-Rising Stem Hard Seal Gate Valve (DN40-DN2000), pressure: (Class125/Class150), all the products pass CE pressure equipment Certification.

Size Range: 1 1/2“-24”/DN40-DN600  

Operate: Handhweel/Gear Box/Pneumatic/Electric-Motorized

Working Pressure: Class 125/Class 150

Body Materials: ASTM A126/A536

Disc Materials: ASTM A126/A536

Seat Materials: Brass/Bronze/SS

Stem Materials: SS

Gland: ASTM A126/A536

Application for: Water,Oil &Gas

Shell Test:1.5 times

Seat Test:1.1 times

Payment: T/T, D/P or L/C

Lead Time:5-30 days

Description

Introduction:

The opening and closing part of the gate valve is a gate. The movement direction of the gate is perpendicular to the direction of the fluid. The gate valve can only be fully opened and fully closed, and cannot be adjusted or throttled. The gate has two sealing surfaces. The two sealing surfaces of the most commonly used model gate valve form a wedge. The wedge angle varies with valve parameters, usually 50, and 2°52' when the medium temperature is not high. The gate of the wedge gate valve can be made into a whole, called a rigid gate; it can also be made into a gate that can produce a small amount of deformation to improve its manufacturability and compensate for the deviation of the sealing surface angle during the processing. The plate is called an elastic gate.


Features:

1. Exquisite selection of materials, in line with relevant standards, and high quality materials.

2. The valve fully meets the requirements of the standard, with reliable sealing, excellent performance and beautiful appearance.

3. The sealing pair is advanced and reasonable. The sealing surfaces of the gate and the valve seat are made of Stellite cobalt-based hard alloys with different hardness. The sealing is reliable, high hardness, wear resistance, high temperature resistance, and high temperature resistance. Good corrosion and scratch resistance and long life.

4. After quenching and tempering and surface nitriding treatment, the valve stem has good corrosion resistance, scratch resistance and wear resistance.

5. It adopts wedge-type elastic gate structure, middle and large diameters are equipped with thrust bearings, the friction is small, and it is equipped with impact manual operation, which can be opened and closed easily.


Design advantages:

1. The fluid resistance is small, and the sealing surface is less brushed and corroded by the medium.

2. It saves effort to open and close.

3. The flow direction of the medium is not restricted, does not disturb the flow, and does not reduce the pressure.

4. Simple shape, short structure length, good manufacturing technology and wide application range.


Field of Application:

Size Range: DN40 to DN600

Temperature: (-)29℃ to 425℃

Allowable Operating Pressure:Class 125/Class 150

Gate valve is widely used in petrochemical plants, metallurgy, water treatment, thermal power plants and other oil and water vapor pipelines to connect or cut off the medium in the pipeline.


Technical Specification:

1.Face to face :ANSI B16.10 

2.Flange ends:ASME B16.10

3.Class 125: Flat flange

4.Class 150: Raised face flange


Installation and maintenance:

1. Handwheels, handles and transmission mechanisms are not allowed to be used for lifting, and collisions are strictly prohibited.

2. The double gate valve should be installed vertically (that is, the valve stem is in the vertical position and the handwheel is on the top).

3. The gate valve with bypass valve should be opened before opening (to balance the pressure difference between inlet and outlet and reduce the opening force).

4. The gate valve with drive mechanism should be installed according to the product manual.

5. If the valve is frequently opened and closed, lubricate at least once a month.

2Tss.jpg

MATERIAL LIST

Part ANSI Material   Material
Body ASTM A126/A536Cast Iron/Ductile Iron
Disc ASTM A126/A536Cast Iron/Ductile Iron
Seat Brass/Bronze
Stem SS
Gland ASTM A126/A536Cast Iron/Ductile Iron



Dimensions (mm)

DN Inch L PCD (CL125/150) FOD n-φd
40 1 1/2" 165 98.5 127 4-16
50 2" 178 120.7 152 4-19
65 22/1" 191 139.7 178 4-19
80 3" 203 152.4 191 4-19
100 4" 229 190.5 229 8-19
125 5" 254 215.9 254 8-22
150 6" 267 241.3 279 8-22
200 8" 292 298.5 343 8-22
250 10" 330 362 406 12-25
300 12" 356 431.8 483 12-25
350 14" 381 476 533 12-29
400 16" 406 540 597 16-29
450 18" 432 578 635 16-32
500 20" 457 638 699 20-32
600 24" 508 749 813 20-35


send inquiry to us

Related Product

Chat with us