DIN F4 Cast Iron/Ductile Iron Rising Stem Hard Seal Gate Valve——ZG VALVE
DIN F4 Cast Iron/Ductile Iron Rising Stem Hard Seal Gate Valve——ZG VALVE
  • DIN F4 Cast Iron/Ductile Iron Rising Stem Hard Seal Gate Valve——ZG VALVE
  • DIN F4 Cast Iron/Ductile Iron Rising Stem Hard Seal Gate Valve——ZG VALVE

DIN F4 PN10/PN16 Cast Iron/Ductile Iron Rising Stem Hard Seal Gate Valve

ZG VALVE DIN F4 PN10/PN16 Cast Iron/Ductile Iron Rising Stem Hard Seal Gate Valve(DN40-DN600), CE pressure equipment Certification,10 inspection procedures, multiple pressure tests,two-year warranty, a variety of materials are available.

Size Range: 1 1/2“-24”/DN40-DN600  

Operate: Handhweel/Gear Box/Pneumatic/Electric-Motorized

Working Pressure: PN10/PN16

Body Materials: Cast Iron/Ductile Iron

Disc Materials: Cast Iron/Ductile Iron

Seat Materials: Brass/Bronze/SS

Stem Materials: SS

Gland Materials: Cast Iron/Ductile Iron

Application for: Water,Oil &Gas

Shell Test:1.5 times

Seat Test:1.1 times

Payment: T/T, D/P or L/C

Lead Time:5-30 days

Description

Introduction:

The opening and closing part of the gate valve is a gate. The movement direction of the gate is perpendicular to the direction of the fluid. The gate valve can only be fully opened and fully closed, and cannot be adjusted or throttled. The gate has two sealing surfaces. The two sealing surfaces of the most commonly used model gate valve form a wedge. The wedge angle varies with valve parameters, usually 50, and 2°52' when the medium temperature is not high. The gate of the wedge gate valve can be made into a whole, called a rigid gate; it can also be made into a gate that can produce a small amount of deformation to improve its manufacturability and compensate for the deviation of the sealing surface angle during the processing. The plate is called an elastic gate.


Features:

1. Exquisite selection of materials, in line with relevant standards, and high quality materials.

2. The valve fully meets the requirements of the standard, with reliable sealing, excellent performance and beautiful appearance.

3. The sealing pair is advanced and reasonable. The sealing surfaces of the gate and the valve seat are reliable, high hardness, wear resistance, high temperature resistance, and high temperature resistance. Good corrosion and scratch resistance and long life.

4. After quenching and tempering and surface nitriding treatment, the valve stem has good corrosion resistance, scratch resistance and wear resistance.

5. It adopts wedge-type elastic gate structure, middle and large diameters are equipped with thrust bearings, the friction is small, and it is equipped with impact manual operation, which can be opened and closed easily.


Design advantages:

1. The fluid resistance is small, and the sealing surface is less brushed and corroded by the medium.

2. It saves effort to open and close.

3. The flow direction of the medium is not restricted, does not disturb the flow, and does not reduce the pressure.

4. Simple shape, short structure length, good manufacturing technology and wide application range.


Field of Application:

Size Range: DN40 to DN600

Temperature: (-)29℃ to 425℃

Allowable Operating Pressure:PN10/PN16

Gate valve is widely used in petrochemical plants, metallurgy, water treatment, thermal power plants and other oil and water vapor pipelines to connect or cut off the medium in the pipeline.


Technical Specification:

1.Face to face: DIN3202-F4 

2.Flange ends: DIN2532/2533/2501


Installation and maintenance:

1. Handwheels, handles and transmission mechanisms are not allowed to be used for lifting, and collisions are strictly prohibited.

2. The double gate valve should be installed vertically (that is, the valve stem is in the vertical position and the handwheel is on the top).

3. The gate valve with bypass valve should be opened before opening (to balance the pressure difference between inlet and outlet and reduce the opening force).

4. The gate valve with drive mechanism should be installed according to the product manual.

5. If the valve is frequently opened and closed, lubricate at least once a month.

7Tss.jpg


MATERIAL LIST

Part Material   
Body Cast Iron/Ductile Iron
Disc Ductile iron/SS
Seat Brass/Bronze/SS
Stem SS/Brass
O-Ring NBR
NutBrass/Bronze


Dimensions (mm)

DN Inch L PN10 PN16
PCD n-φd FOD PCD  n-φd FOD
40 1 1/2" 140 110 4-18 150 110 4-18 150
50 2" 150 125 4-18 165 125 4-18 165
65 22/1" 170 145 4-18 185 145 4-18 185
80 3" 180 160 8-18 200 160 8-18 200
100 4" 190 180 8-18 220 180 8-18 220
125 5" 200 210 8-18 250 210 8-18 250
150 6" 210 240 8-22 285 240 8-22 285
200 8" 230 295 8-22 340 295 12-22 340
250 10" 250 350 12-22 395 355 12-26 405
300 12" 270 400 12-22 445 410 12-26 460
350 14" 290 460 16-22 505 470 16-26 520
400 16" 310 515 16-26 565 525 16-30 580
450 18" 330 565 20-26 615 585 20-30 640
500 20" 350 620 20-26 670 650 20-33 715
600 24" 390 725 20-30 780 770 20-36 840


Related Product

Chat with us